TephraXMOD V1
#49
Evolving Member
iTrader: (5)
this came up on the other forums regarding the meth fail safe function and i thought i'd add it here as well
Once the ecu pin is grounded AND you are BELOW the load threshold the defined counter begins. once the counter reaches its value alt maps active.
my settings
switch:4
load:100
timer:3000
so if my meth kit give the "ok" by the fail safe wire being grounded and i am below 100 load for 3 seconds my meth tune turns on.
if at any time my failsafe is activated (ground removed) I INSTANTLY switch to my standard pump tune. a ton of fuel is added, timing is pulled and boost drops to safe 93 octane levels. I will remain on my 93 pump tune until my meth kit gives the "ok" again (by turning the ground back on) and i am below 100 load for 3 seconds. this is because if your doing a pull it will switch to the safe map until your off the throttle preventing the maps from toggling back and forth
how ****ing cool is that?
<3 ya T!
Once the ecu pin is grounded AND you are BELOW the load threshold the defined counter begins. once the counter reaches its value alt maps active.
my settings
switch:4
load:100
timer:3000
so if my meth kit give the "ok" by the fail safe wire being grounded and i am below 100 load for 3 seconds my meth tune turns on.
if at any time my failsafe is activated (ground removed) I INSTANTLY switch to my standard pump tune. a ton of fuel is added, timing is pulled and boost drops to safe 93 octane levels. I will remain on my 93 pump tune until my meth kit gives the "ok" again (by turning the ground back on) and i am below 100 load for 3 seconds. this is because if your doing a pull it will switch to the safe map until your off the throttle preventing the maps from toggling back and forth
how ****ing cool is that?
<3 ya T!
#51
Evolved Member
iTrader: (10)
David,
So I switched everything over to the latest version you sent us / posted on evoM. The map switching for cruise control does not work now... it will not switch maps to the alt. There is no indication from ICS light. I tried messing with time settings and no map switch. The previous version worked... this one does not.
not sure what is going on.
I tried twice... to copy everything over and change... still no map switch...
So I switched everything over to the latest version you sent us / posted on evoM. The map switching for cruise control does not work now... it will not switch maps to the alt. There is no indication from ICS light. I tried messing with time settings and no map switch. The previous version worked... this one does not.
not sure what is going on.
I tried twice... to copy everything over and change... still no map switch...
#54
Evolved Member
iTrader: (1)
Join Date: Nov 2009
Location: Omaha, NE
Posts: 1,456
Likes: 0
Received 0 Likes
on
0 Posts
Clipse, mine works just fine on 55570106 rom (aka Tephra's 55570006).
Do you have the Alt-Map Load Threshold set low? I know I made that mistake. Make sure it is set to ~100. You must be under that load for it to work.
Maybe send your ROM to Tephra to have a look.
Do you have the Alt-Map Load Threshold set low? I know I made that mistake. Make sure it is set to ~100. You must be under that load for it to work.
Maybe send your ROM to Tephra to have a look.
#56
Evolved Member
iTrader: (3)
Sorry for thread jack...
If your coming from Evo 7-9 you may notice that there is a slight difference in the algorithm. NOW the CEL lamp will only flash when the knock STARTS above the thresholds. I have done this to stop low load knock from causing the CEL to flash when you pass above the load threshold.
Dave,
Any chance this revised CEL algorithm can be added to the Tephra V7 for VIII's and IX's?
#60
Evolved Member
iTrader: (49)
Maybe I'm just retarded, but what is your Paypal address? I tried paypaldonations@globalshare.net and it says that address is not a registered user.