EvolutionM - Mitsubishi Lancer and Lancer Evolution Community

Notices

TephraXMOD V1

Thread Tools
 
Search this Thread
 
Old Jul 7, 2010, 07:09 PM
  #181  
Evolved Member
iTrader: (6)
 
EvoX2NR's Avatar
 
Join Date: Nov 2008
Location: Jacksonville, FL
Posts: 564
Received 0 Likes on 0 Posts
P0183
EvoX2NR is offline  
Reply Like
Old Jul 7, 2010, 07:12 PM
  #182  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
... and did you cut the fuel tank temp sensor wire?
tephra is offline  
Reply Like
Old Jul 7, 2010, 07:16 PM
  #183  
Evolved Member
iTrader: (6)
 
EvoX2NR's Avatar
 
Join Date: Nov 2008
Location: Jacksonville, FL
Posts: 564
Received 0 Likes on 0 Posts
I tried cutting it and the code came back right away.
EvoX2NR is offline  
Reply Like
Old Jul 7, 2010, 07:20 PM
  #184  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
ok well your ONLY meant to cut that wire IF your using altmap master mode 4 (Resistor ADC)...

reconnect the wire, and clear the code... it shouldn't come back...
tephra is offline  
Reply Like
Old Jul 7, 2010, 07:21 PM
  #185  
Evolved Member
iTrader: (6)
 
EvoX2NR's Avatar
 
Join Date: Nov 2008
Location: Jacksonville, FL
Posts: 564
Received 0 Likes on 0 Posts
Originally Posted by tephra
ok well your ONLY meant to cut that wire IF your using altmap master mode 4 (Resistor ADC)...

reconnect the wire, and clear the code... it shouldn't come back...

LOL, I cut it in the first place because I was trying to make it go away.
EvoX2NR is offline  
Reply Like
Old Jul 7, 2010, 07:22 PM
  #186  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
ok now that you have cut it - can you try running altmap master = 4 and see if it comes back (after you clear it)

if thats ok, then reconnect the wire and switch back to altmap master = 2 (cruise control)
tephra is offline  
Reply Like
Old Jul 7, 2010, 07:26 PM
  #187  
Evolved Member
iTrader: (6)
 
EvoX2NR's Avatar
 
Join Date: Nov 2008
Location: Jacksonville, FL
Posts: 564
Received 0 Likes on 0 Posts
Originally Posted by tephra
ok now that you have cut it - can you try running altmap master = 4 and see if it comes back (after you clear it)

if thats ok, then reconnect the wire and switch back to altmap master = 2 (cruise control)
I will once I get access to a cable. Unfortunately I wasn't the person who put this on the ecu. I am going to give the resistor a shot tomorrow and see what happens...
EvoX2NR is offline  
Reply Like
Old Jul 7, 2010, 07:34 PM
  #188  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
if your NOT using Resistor ADC mode (altmap master = 4) then just reconnect the wire... its probably better your ECU knows what the fuel tank temperature is.

the 250ohm resistor will be too LOW anyways, you should be using 5k...

but reconnect it and then go from there
tephra is offline  
Reply Like
Old Jul 7, 2010, 08:16 PM
  #189  
Newbie
 
EvoXCR's Avatar
 
Join Date: Jun 2010
Location: Costa Rica
Posts: 10
Likes: 0
Received 0 Likes on 0 Posts
I was checking the wiring when I saw Tephra's post... no lines from C130 connector to the ECU. Had to build the harness. It's now working for turning the cruise control on/off and switching between maps but the cruise control itself is not working.

Any thoughts?

Thanks
Last edited by EvoXCR; Jul 7, 2010 at 09:14 PM.
EvoXCR is offline  
Reply Like
Old Jul 7, 2010, 10:39 PM
  #190  
Evolved Member
iTrader: (1)
 
Golden's Avatar
 
Join Date: Nov 2009
Location: Omaha, NE
Posts: 1,456
Likes: 0
Received 0 Likes on 0 Posts
Code is probably not in your ROM. Or it's disabled.
Golden is offline  
Reply Like
Old Jul 7, 2010, 10:44 PM
  #191  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
there might be a pbit or something to enable cruise...

ill have a look when i can
tephra is offline  
Reply Like
Old Jul 8, 2010, 08:22 AM
  #192  
Newbie
 
EvoXCR's Avatar
 
Join Date: Jun 2010
Location: Costa Rica
Posts: 10
Likes: 0
Received 0 Likes on 0 Posts
While rechecking there seems to be no line from the brake pedal to the ECU. Will check on that and keep you guys posted.

Thanks for your help!
EvoXCR is offline  
Reply Like
Old Jul 9, 2010, 04:27 PM
  #193  
Account Disabled
iTrader: (8)
 
GST Motorsports's Avatar
 
Join Date: Sep 2007
Location: Hayward
Posts: 3,366
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by tephra
55590007 is the latest afaik... bryan is testing the tephraxmod for that rom as we speak
Tested, map switching works. Only problem is the 2010 RA physically has no IC spray icon to blink when on alt map.

(The RA has a different cluster then the Evo)

Tephra, you haz email.

- Bryan
GST Motorsports is offline  
Reply Like
Old Jul 9, 2010, 04:36 PM
  #194  
Former Sponsor
iTrader: (1)
 
HB Speed's Avatar
 
Join Date: Oct 2008
Location: Tuning AWD's In socal !!
Posts: 682
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by GST Motorsports
Tested, map switching works. Only problem is the 2010 RA physically has no IC spray icon to blink when on alt map.

(The RA has a different cluster then the Evo)

- Bryan
Made 375 whp on 91 on dom2 with this last night!!
HB Speed is offline  
Reply Like
Old Jul 9, 2010, 05:24 PM
  #195  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
yep im looking into it..
tephra is offline  
Reply Like



Advanced Search
Quick Reply: TephraXMOD V1


Reply Closed Thread Share

All times are GMT -7. The time now is 11:20 AM.